Influence of Peak Austenitizing Temperature and Thermal Transformation Kinetics on the Degradation of High-Strength Low-Alloy Steel in Chloride Environments

Osamah Alsudani

doi:10.71229/p6n19b03

Authors

Osamah Alsudani College of Engineering, University of Misan, Al Amarah City, Misan Province, 62001, Iraq.

DOI:

https://doi.org/10.71229/p6n19b03

Keywords:

High-Strength Low-Alloy (HSLA) Steel, Thermal Transformation Kinetics, Zener Pinning Stabilization

Abstract

One of the main challenges in marine engineering is the microscale evolution of microstructures and corrosion in alloys. The work focuses on whether thermal transformation kinetics, mechanical microanisotropy, and average macroscopic corrosion rates in A572 high-strength low-alloy steel are related. Three different austenitizing peak temperatures and cooling rates were applied to produce the three microstructural regimes. The samples were evaluated using optical microscopy, static laboratory testing (ASTM G31) in 3.5 % NaCl solution, and spatial Vickers microhardness testing. A correlation between electrochemical degradation and microstructural coarsening has been observed in experimental results. Carbonitride precipitates were not removed from the fine-grained matrix from a thermal-kinetic perspective, a requirement for the formation of the highly polished, interlocking morphology produced by low-thermal-input synthesis. This homogenized structural state exhibited excellent corrosion resistance, with a rate of 0.150 millimeters per year, and effectively minimized general mass loss. On the other hand, a thermodynamically supersaturated condition led to the formation of ordered bainitic packets and macroscopic softening, thereby accelerating the overall degradation rate. Extensive abnormal grain growth (Widmanstätten ferrite plates) was induced by the dissolution of precipitates under the extreme thermal cycle established for stabilization. This complex morphology led to a high anodic-to-cathodic area ratio and large interfacial strain gradients, resulting in a high corrosion rate of 0.402 mm/yr. In addition, spatial microhardness profiling has shown that high standard deviations of local hardness accurately reflect phase mismatches that cause galvanic susceptibility. Lastly, the current study reveals strong mechanical anisotropy effects in electrochemical degradation processes and indicates that local hardness variation is indicative of relative corrosion susceptibility.

References

[1] E. Ura-Bińczyk, “Effect of grain refinement on the corrosion resistance of 316L stainless steel,” Materials, vol. 14, no. 24, Dec. 2021, doi: 10.3390/ma14247517.

[2] G. Palumbo et al., “Effect of grain size on the corrosion behavior of Fe-3wt.%Si-1wt.%Al electrical steels in pure water saturated with CO2,” Materials, vol. 14, no. 17, Sep. 2021, doi: 10.3390/ma14175084.

[3] S. Kar, A. Yilmaz, K. Traka, J. Sietsma, and Y. Gonzalez-Garcia, “Role of Grain Size and Recrystallization Texture in the Corrosion Behavior of Pure Iron in Acidic Medium,” Metals (Basel)., vol. 13, no. 2, Feb. 2023, doi: 10.3390/met13020388.

[4] J. I. Ahuir-Torres et al., “A Study of the Corrosion Resistance of 316L Stainless Steel Manufactured by Powder Bed Laser Additive Manufacturing,” Applied Sciences (Switzerland), vol. 14, no. 17, Sep. 2024, doi: 10.3390/app14177471.

[5] X. Fu, Y. Ji, X. Cheng, C. Dong, Y. Fan, and X. Li, “Effect of grain size and its uniformity on corrosion resistance of rolled 316L stainless steel by EBSD and TEM,” Mater. Today Commun., vol. 25, p. 101429, Dec. 2020, doi: 10.1016/j.mtcomm.2020.101429.

[6] M. S. Anwar, R. R. Widjaya, L. B. A. Prasetya, A. A. Arfi, E. Mabruri, and E. S. Siradj, “Effect of Grain Size on Mechanical and Creep Rupture Properties of 253 MA Austenitic Stainless Steel,” Metals (Basel)., vol. 12, no. 5, May 2022, doi: 10.3390/met12050820.

[7] A. A. Fadiel, “A Comprehensive Comparative Review of Corrosion Behavior, Mechanisms, and Protection Strategies for Metallic Materials in Marine Environments Methodology,” Journal of Physics and Chemistry Research, vol. 7, no. 3, 2018, doi: 10.36266/JPCR/191.

[8] T. Li, D. Wang, S. Zhang, and J. Wang, “Corrosion Behavior of High Entropy Alloys and Their Application in the Nuclear Industry—An Overview,” Feb. 01, 2023, MDPI. doi: 10.3390/met13020363.

[9] H. Wang, P. Jiang, G. Yang, and Y. Yan, “An Investigation of the Anisotropic Mechanical Properties of Additive-Manufactured 316L SS with SLM,” Materials, vol. 17, no. 9, May 2024, doi: 10.3390/ma17092017.

[10] K. D. Ralston and N. Birbilis, “Effect of Grain Size on Corrosion: A Review,” Corrosion, vol. 66, no. 7, pp. 075005-1-075005–13, Jul. 2010, doi: 10.5006/1.3462912.

[11] B. Dong et al., “Corrosion Mechanism and Applicability Assessment of N80 and 9Cr Steels in CO2 Auxiliary Steam Drive,” J. Mater. Eng. Perform., vol. 28, no. 2, pp. 1030–1039, Feb. 2019, doi: 10.1007/s11665-018-3847-z.

[12] H.-Y. Ha, J.-Y. Kang, T.-H. Lee, H. Park, and H. Kim, “Effect of Grain Size on the Pitting Corrosion Resistance of Lean Duplex Stainless Steel,” Steel Res. Int., vol. 94, no. 2, Feb. 2023, doi: 10.1002/srin.202200227.

[13] E. Hug, C. Keller, C. Folton, J. Papin, K. Tabalaiev, and G. Marnier, “Ultrafine Grain 316L Stainless Steel Manufactured by Ball Milling and Spark Plasma Sintering: Consequences on the Corrosion Resistance in Chloride Media,” Metals (Basel)., vol. 14, no. 8, Aug. 2024, doi: 10.3390/met14080864.

[14] M. Majid, E. A. Khalid, and H. Zghair, “Corrosion and Microhardness Behavior Improvement of 316L Stainless Steel via Fiber Laser Surface Treatment,” Al-Khwarizmi Engineering Journal, vol. 20, no. 4, pp. 46–57, Dec. 2024, doi: 10.22153/kej.2024.12.002.

[15] D. Wang, Q. Zhong, J. Yang, and S. Zhang, “Effects of Cr and Ni on the microstructure and corrosion resistance of high-strength low alloy steel,” Journal of Materials Research and Technology, vol. 23, pp. 36–52, Mar. 2023, doi: 10.1016/j.jmrt.2022.12.191.

[16] R. Galván-Martínez et al., “Effect of Hydrodynamic Conditions on the Corrosion Mechanism of HSLA X100 Steel by EIS and EN Analysis,” Surfaces, vol. 8, no. 1, Mar. 2025, doi: 10.3390/surfaces8010010.

[17] K. Song et al., “Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing,” Metals (Basel)., vol. 13, no. 4, Apr. 2023, doi: 10.3390/met13040764.

[18] T. Ślęzak, “Welding of S960QL High-Strength Steel by the Manual–Automated MAG Technique—A Study of Mechanical Properties, Residual Stresses and Fracture Mechanisms in the Heat-Affected Zone,” Materials, vol. 17, no. 23, Dec. 2024, doi: 10.3390/ma17235792.

[19] Y. Wang et al., “Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel,” Coatings, vol. 13, no. 8, Aug. 2023, doi: 10.3390/coatings13081442.

[20] Y. Yang, X. M. Zhao, H. Li, X. Y. Zhao, and H. Bin Han, “The effect of inclusions on a medium temperature transformation microstructure and toughness of high-strength hsla steel,” Materials, vol. 14, no. 16, Aug. 2021, doi: 10.3390/ma14164424.

[21] D. Song et al., “Corrosion behavior and mechanism of Cr–Mo alloyed steel: Role of ferrite/bainite duplex microstructure,” J. Alloys Compd., vol. 809, Nov. 2019, doi: 10.1016/j.jallcom.2019.151787.

[22] A. Furquim Junior et al., “Effect of Welding Heat Input on Corrosion Behavior of Duplex Stainless Steel Welding Overlay on Carbon Steel,” Metals (Basel)., vol. 16, no. 2, Feb. 2026, doi: 10.3390/met16020207.

[23] N. Yadav and G. G. Roy, “Effect of Mischmetal Treatment on the Microstructure, Tensile Properties, and Fracture Behavior of Hot Compressed Low-Carbon Aluminum-Killed (LCAK) Steel,” Metallurgical and Materials Transactions A, vol. 56, no. 12, pp. 5799–5816, Dec. 2025, doi: 10.1007/s11661-025-08015-9.

[24] G. Yalçıner, G. Özer, A. Kisasoz, and A. Karaaslan, “Influence of the phase balance and cooling conditions on the microstructure and corrosion behavior of solution-treated 1.4462 duplex stainless steel,” Mater. Res. Express, vol. 6, no. 12, p. 1265i5, Jan. 2020, doi: 10.1088/2053-1591/ab6f3a.

[25] M. Palcut, R. Tomšová, P. Priputen, Ž. Gerhátová, M. Sahul, and M. Kusý, “Bulk Al-Al9Co2 alloys: Microstructure, corrosion behavior and hydrogen evolution kinetics,” Corros. Sci., vol. 222, p. 111409, Sep. 2023, doi: 10.1016/j.corsci.2023.111409.

[26] R. Otterberg, R. Sandström, and A. Sandberg, “Influence of Widmanstätten ferrite on mechanical properties of microalloyed steels,” Metals Technology, vol. 7, no. 1, pp. 397–408, Jan. 1980, doi: 10.1179/030716980803286658.

[27] Y. Liu et al., “Evolution of Microstructures and Mechanical Properties with Tempering Temperature in a Novel Synergistic Precipitation Strengthening Ultra-High Strength Steel,” Materials, vol. 17, no. 21, Nov. 2024, doi: 10.3390/ma17215314.

[28] Y. Mazaheri, A. Kermanpur, and A. Najafizadeh, “Nanoindentation study of ferrite–martensite dual phase steels developed by a new thermomechanical processing,” Materials Science and Engineering: A, vol. 639, pp. 8–14, Jul. 2015, doi: 10.1016/j.msea.2015.04.098.

[29] Z. Li, Y. Chang, W. Liu, and J. Lian, “Predicting edge fracture in dual-phase steels: Significance of anisotropy-induced localization,” Int. J. Mech. Sci., vol. 274, Jul. 2024, doi: 10.1016/j.ijmecsci.2024.109255.

[30] K. Lei et al., “Microstructure and Properties of Corrosion-Resistant Steel Produced by CASTRIP,” Crystals (Basel)., vol. 15, no. 7, Jul. 2025, doi: 10.3390/cryst15070595.